The system comprises of a heavy gauge aluminium pole to which the banner is sleeved. The pole is secured into a steel electro-plated bracket with a removable plated locking pin. Plastic collars retain the banner from both sides. The standard system is good but does not compensate for expansion of PVC due to wind and heat. This leads to a 'slap' factor that can destroy both the banner and the fittings.
The wall mount bracket is 75mm wide and 130mm deep. It has 4 pre-drilled holes suitable for M8 fixings. We can supply the M8 sleeve anchor bolts at 55mm or 70mm long.
Here is a true self-tensioning banner system that is low cost, high value, very effective and displays your graphics to their best effect whatever the weather. The standard system is good but does not compensate for expansion of PVC due to wind and heat. This leads to a 'slap' factor that can destroy both the banner and the fittings. Our self-tensioning system helps to alleviate these problems. Easy to install, easy to adjust, easy to see why this is going to be the system your customer prefers.
Wire Supported System
A conversion kit that will safely handle banner sizes up to 6mtr x 1mtr. This is a wall mounted heavy duty support that takes the strain out of fitting big banners.
Standard System
The system comprises of a heavy gauge aluminium pole to which the banner is sleeved.
Max Banner Width 915mm
Self-Tensioning System
Here is a true self-tensioning banner system that is low cost, high value, very effective and displays your graphics to their best effect whatever the weather.
Post Mounted Wire Supported System
There is a natural tendency for banner poles to droop. Keeping a banner properly tensioned adds to its life and gives a much better presentation to it's image.
You can upgrade your existing post-mounted system by just buying the additional kit.
Heavy Duty Post Mount System
This versatile high-strength aluminium bracket fits lamp-post diameters from 75 mm to 150 mm, making it applicable in almost every situation. Fitted singly or in pairs, the oval section pole fits securely on to the bracket and supports. Used in pairs to tension the banner. Suitable for banners with areas up to 2 m2.
The Standard Post Mount Bracket offers an alternate approach to fixing banners to steel lighting posts and other vertical columns. The system comprises a heavy gauge aluminium pole to which the banner is sleeved. The pole is secured into a pressed steel bracket by means of a removable locking pin.
Make your message the centre of attention. The Mid Mount System secures banners singly or back to back on the centre of a lamppost. Banners are sleeved top and bottom, the unique spring tensioner system keeps everything taught but allows it to flex in the wind.
Suction Mounted Banner Arm
The Suction Mounted Arm is an innovative solution to a common problem, allowing installation of banners where drilling isn't possible or space simply isn't available for a conventional system.
* Mount on to any non-porous surface such as glass, sheet metals or plastics
* Installed in a matter of seconds
* Can be used singly or in pairs
* Ideal in situations where planning authorities restrict the use of street signage Suction units are turned on and off with a removable key making them vandal resistant
* Suitable for use with banners with areas up to 1 sq. metre
* Twin heavy duty suction units with removable locking keys
* 40 mm diameter x 500 mm length plastic arm fitted with end cap and collar
Face Fix Wall Mount System
The Face Fix system is an increasingly popular exterior promotional tool, commonly used on free wall spaces and gable ends. The system enables large banners to be secured flat to a wall with the ability to change and tension the banner easily. Features Heavy Duty steel brackets with pre-drilled 16 mm fixing holes, 60 mm aluminium cross bars, tension bar and stainless steel rigging screws and fittings. Banners are quickly installed and changed by sliding onto the cross bars and tightening the rigging screws.
Banner Rail
The outdoor promotions market has been screaming for a system, which enables a banner to be changed in seconds and which avoids repeated, drilling and screwing by maintenance people. You only install this system once. The Banner Rail is new, original and it works!!
Install it once...Change the banner easily forever!
The Shop Front Sign
Designed to secure a PVC banner flat to wall, The Shop Front Sign is easily removed to enable safe overnight storage inside your premises. The banner is tensioned with elastics ensuring it is always smartly displayed and rapidly changed.
Free standing banner frames
Our range of Banner Frames aims to offer a high quality solution for any location or type of event - and we welcome requests for any unusual or non-standard type of frame. We will always do our best to provide a first class answer.
Double-Sided
Our Standard Banner Frames can also be supplied in Double Frame format to allow banners to be attached to either side when all-round visibility is needed. Struts can be added for extra support where necessary.
Overhead Banner Frames
If you need your message to stand head and shoulders above the rest, the Overhead Banner Frame is an ideal solution. To ensure your prominently-positioned banner looks its best throughout the event, the banner is sleeved on to the cross bar of the Overhead Frame.
Click here for information on internal banners